Question 2: Why can't the printer cartridge be filled with more ink? You can't print after adding ink. May be when adding ink into the air, ink can't print out.
There will be many customers who, after receiving the uv 16 10 universal printer machine, are in a hurry to add ink, but they do not carefully read the instructions provided and operate the video CD, and directly add ink to the small ink cartridge. Some customers also think that the ink must be filled up. Tell you responsibly: these practices are all wrong.
First of all, on the left side of the universal flat-panel printer, there is a special label "Ink adding place". Open the small door and you will see a row of "ink bottles". You should add ink from here.
Secondly, when adding ink, don't fill it up, just add half, because the working principle of continuous ink supply cartridge is different from that of filling cartridge. If it is full, on the one hand, there is no air pressure, and ink can't be supplied to the small ink box, resulting in ink shortage in printing; On the other hand, it is prone to ink dripping.
Finally, pay attention to the order of adding ink, and don't add it wrong.
Question 3: How to enter the code after adding ink to Epson printer? Please confirm your printer model first, whether it is (L 10 1, L20 1, L30 1) printer.
1. You can click "Start->" in the lower left corner of the computer; "devices and printers" or "printers and faxes", right-click the icon of the printer used and select "printing preferences"->; "maintenance"->; "Epson Status Monitor", there will be a "How to" button in this window when the ink quantity is insufficient or exhausted. Click here to open the window for entering the ID number. Please follow the onscreen instructions.
Note: If the ink indicator is flashing, you can continue to use it until the ink indicator is always on, and then enter the ID number to reset.
2. Non -(L20 1) ink quantity. L 10 1, L80 1) The printer count is an estimated value, which may cause errors with the actual ink quantity due to some operations in actual use.
When the ink lamp is always on, please fill it with ink (it is recommended to fill all four-color ink bins), then press the printer's maintenance key (inverted triangle key) to reset the ink and turn off the ink lamp.
Tip:
Please pay attention to the ink capacity of the ink cartridge. When the ink amount is less than 20 mm, please replenish the ink in time to avoid the failure of the print head.
The ink light is on all the time. If there is no response when pressing the maintenance key, please press and hold the printer's maintenance key (inverted triangle key) and lightly wipe it twice.
If the above scheme still can't solve your problem, please log in to Epson official website "Online Engineer": 219.232.55.146/portal/epson to communicate with Epson engineers in real time and solve the problem in time. (Epson "Online Engineer" service hours: 9: 00- 18: 00 from Monday to Friday)
Question 4: How to add ink to Canon mp288 printer? Hello, if you add ink yourself, it's about 3-5ML. This is easy to leak ink, and the success rate of adding ink is not very high. Now there is a new product on the market, Canon Easy-to-Add Ink-jet Cartridge, which can add 25ML ink at a time and can add ink for more than 20 times. The printing volume is dozens of times that of the original ink cartridge. Printing costs less than a penny and is more cost-effective. If necessary, you can go and have a look
Question 5: How to operate Canon g2800 printer directly after adding ink?
Question 6: How can a novice fill up the printer's ink cartridge 1? The small hole under the self-adhesive label of the ink cartridge is the ink filling position ... use a small drill to drill a hole corresponding to the ink cartridge to be added ... subject to the needle tube.
2. Pay attention to the following three points when adding ink: (a) Pay attention when drilling under the glue with a drill. This hole is not particularly easy to drill, but don't use too much force when drilling. (b) Use a graduated disposable syringe to add about 5-8 ml of black at a time; Add about 3-5 ml of each color. When adding colors, be careful not to let water of other colors touch another color. (c) Because these two types of ink cartridges are designed to integrate ink cartridges and nozzles. When drilling or adding ink, try not to touch the metal contacts and nozzles on the ink cartridge. Another special thing to note is that the needle should be inserted into the bottom edge and added slowly. The ink cartridge is high-density foam, which absorbs water very slowly. (Note: After this type of ink cartridge is filled with ink, it may have been rejected on the computer at that time. Stay for a while, and you will return to normal. After adding ink, the ink quantity display will be invalid. )
From 20 10, 10-Buy and send to Zhuhai Dan Jun Printing Supplies Co., Ltd. In order to give back to the support, trust and care of the majority of users for Dan Jun, these days, we have launched _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Question 7: Why does the printer only add ink or often prompt for lack of ink? Some printers run out of ink, which is determined by the ink cartridge chip. Even after adding ink again, it still shows lack of ink and can be used normally. If it's Epson's machine, be sure to refresh the chip as much as possible, otherwise it won't work after adding ink.
Question 8: How to add ink to the ink cartridge of the new Thunder printer? 1. Make sure that the machine starts with a running sound. If there is no running sound, the problem still exists after reinstalling printer consumables. It is recommended to contact the local service center.
2. If it works normally, check the computer port. My computer)- Right Click-Management-Device Manager-Universal Serial Bus Controller -USB Printing Support. If the port is unavailable, replace the USB cable of the computer port or replace the computer.
3. The port is normal. Delete the USB printing support and printer icon in printers and faxes, unplug the USB cable, restart the computer, and plug in the USB cable for printing.
4. The problem still exists. It is recommended to reinstall the driver or replace the computer.
Question 9: How does Epson printer ink the ink cartridge? How to fill the ink? Seal the ink outlet of the empty ink cartridge with adhesive tape. Take out 1 color ink from each disposable syringe for injection, check whether the ink is deteriorated or precipitated under the lamp, align the small holes on the ink cartridge and inject them into the corresponding color cells of the ink cartridge respectively. After the disposable syringe is filled with ink, it can be reused next time. ) Never tear off the plastic paper on the ink cartridge. In order to avoid poor sealing and air leakage, each color of ink has two small holes, and it is best to inject ink from the latter hole. Below the previous hole is the ink outlet, and there is a filter screen in the ink box to avoid acupuncture. There is a sponge in the ink cartridge, and with the increase of ink injection times, the ink absorption capacity of the sponge will decrease (this is the first reason why it is best to fill the ink cartridge directly on the printer). After the ink cartridge is full, seal the needle hole with adhesive tape, tear off the adhesive tape that seals the ink outlet at the same time, and weigh it to see if the ink is filled to 70% or 90%. It is best to write down the number of photos printed after the bet ink is printed. After printing about 10 photos of A4 size (1270 can print 20 photos), gently pull a locking bolt under the ink cartridge from the paper outlet (1270 directly next to the ink cartridge) with a small wire, and move the ink cart out (you can see it by taking photos with a flashlight). Open the cover of the ink cartridge (at this time, the ink cartridge should be completely immobile in the ink cartridge), draw out 1 color ink from each disposable syringe for injection, fill a hole behind the ink cartridge with ink, push the ink cartridge back to its original position, and check whether the printing is off, and do not wash it intermittently. In this way, the next time you remove the ink cartridge and replace the chip, * * * can print more than 20 A4-sized photos. When the printer shows that there is no ink (in fact, there may be ink in the ink cartridge), it is time to redo steps 2 and 3. If you don't do the first step, you won't do the fourth step, but when the printer shows that there is still ink, it may be that the ink cartridge is out of ink. I don't know when the ink is really used up, which often makes the photos being printed obsolete. Print out the cold-mounted photos and then cold-mount them yourself. A cold-mounted paper for A4 photos is about a few cents, which not only solves the problem of light resistance, but also can wipe the dust on the photo surface with a wet towel. Anyway, it has to be cold mounted. You can print photos at home with good quality inkjet paper. Printers that print large-format photos can print paper with a length of more than 1 m at a time, and divide a photo into several parts on the computer. After printing, you can print large-format photos by bonding, cold mounting or coating. I once printed a 2 m X 4 m large format photo, and the effect was clearer than that of a wide format printer. In short, it is really feasible to print photos with ink! Compared with the original ink cartridge, the quality difference is very small, which is generally difficult to see, and the cost is indeed reduced. However, it must be noted that printing with ink is easy to cause (note that it is "easy to cause" rather than "about to cause") nozzle blockage, which has reached the point where nozzles are scrapped (it may cost hundreds of dollars to replace nozzles), and blind ink injection may not be worth the candle, so novices should pay special attention. For those with poor hands-on ability, small printing volume and abundant hands, it is best to use original or compatible ink cartridges. In addition: Epson ink cartridge is separated from the nozzle, and only the ink cartridge is replaced after the ink is displayed. The spray head is fixed on the printer, and besides being compatible with ink cartridges, it can also be filled with ink at home. Some new Epson printers (870, 875, 680, 790, 890, 895, 1270, 1290, etc. ) Add a small thing to the ink cartridges (color and black ink cartridges), that is, an IC chip to record the remaining amount of ink. If the ink is used up and filled up, it is not necessary to reload the ink cartridge into the printer. It requires both ink cartridges to display ink, because the printer prompts according to the recorded information of the IC chip of the ink cartridge. But if you pry this IC chip open and replace it with a new IC chip, you will still put the ink cartridge in, and the printer will recognize it, even if your ink cartridge is not full! It can't recognize the old IC chip printer installed on the new original ink cartridge. Only Epson knows the real reason for installing this IC chip. In short, the printer recognizes the "core" instead of the "box"! At the same time, it also shows that IC chip can not reflect the real remaining amount of ink. Some consumers complain that Epson ink cartridges do not reflect their real consumption when they provide information about running out of ink. Some ink remains as high as 30% of the total capacity. When one color ink cartridge runs out of ink, the whole ink cartridge can't be used. Epson did not publicly prompt and explain that there was residual ink when his ink cartridge showed that it was short of ink.
Question 10: Why does my printer cartridge still show that it is out of ink after it is filled? The printer monitors the number of ink cartridge chips. Generally speaking, when an ink cartridge runs out of about 6ml of ink, the computer will prompt that the ink is insufficient. Please replace the ink cartridge. Self-ink injection only injects ink into the ink cartridge, and the count of the chip has not changed. As long as you can print things normally, you don't care if there is ink.
You can add a reset chip, which is only a few dollars.