Adjustment method of paper-passing control lever of LQ-630K printer;
The front is facing the printer, and there is a shift lever in the lower right corner of the printer, with two gears, which can be switched back and forth to adjust the forward paper and the backward paper. The position near the printer is to put the paper from the front, and the position away from the printer is to put the paper from the back.
Adjustment method of paper thickness adjusting lever of LQ-630K printer;
Open the translucent cover on the front of the printer and look to the far right. There is a bar that says-1-7. This is to adjust the thickness of the paper. If the printing paper is several layers, dial it to several positions. For A4 paper, dial 1. If it is two or three pages, dial 2 or 3.
Automatic paper cutting method of LQ-630K printer produced before April 20 14;
1. Turn off the printer.
2. Press and hold the "Feed/Return key" and "Pause key" at the same time, then turn on the printer power, press and hold for about 5s, release the print head after it starts to move, and then release the paper, and the printer will print a page of text. Find "automatic paper cutting" in the printed content to see if it is on or off. If so, go to step 3. If it is turned on, it means that automatic paper cutting has been turned on, and step 5 is executed.
3. Press the line feed key twice, the power light goes out, and the paper shortage light and pause light are always on. (Press it once, and the status of the indicator light will change each time. )
4. Press the paper feed key twice, the power light will go out, the paper shortage light will always be on, and the pause light will go out.
5. Close and complete the setup.
Automatic paper cutting method of LQ-630K printer produced after April 20 14;
1. Turn on the printer and load the printing paper. Press the "line feed/page feed (under the project)" button and the "paper feed/paper return (under the project)" button at the same time until the printer beeps and starts printing.
2. Press the "Line feed/Page feed (under the item)" button three times. Every time you press it, the printer will print a line of text, and after the third press, the paper will be cut and printed automatically. Please check whether it is on or off. If it is closed, proceed to the next step (step 3); if it is opened, proceed to step 4, indicating that automatic paper cutting has been opened.
3. Press the "Pause/(Set)" button. After you press it, an "on" will be printed on the back.
4. Press the "Line feed/page feed (under the project)" button and "Paper feed/paper return (under the project)" button at the same time, and the printer will give a long sound to save the settings.
Then, please check whether the paper size you set is exactly the same as the actual continuous paper size. If not, please choose according to the actual paper size. If the relevant paper size cannot be found, please set it as follows:
1. Custom paper:
If your computer is Windows XP:
Click "Start->" in the lower left corner of the computer; "printers and fax machines"->; "file"->; "Server Properties", check "Create a new format", enter the name of the custom size (such as 1234) in "Table Name", and enter "Width" and "Height" (height = number of continuous paper holes *0.5*2.54CM) according to the actual size of the paper. There is no need to modify the printer area margin. Click Save Format to complete the paper customization.
If your computer is Windows 7:
Click "Start->" in the lower left corner of the computer; "Equipment and Printer", click the printer icon with the left mouse button, select "Server Properties" in the upper menu bar, check "New Table", enter a name with a custom size (such as 1234) in "Table Name", and respectively enter "Width" and "Height" (height = number of consecutive holes * 0.5 *) according to the actual paper size. There is no need to modify the printer area margin. Click Save Format to complete the paper customization.
2. Drive settings:
Right-click the printer icon and select Printing Preferences-> "layout"->; "Advanced", in "Paper Specification", select the name of the custom size "1234".
3. Application software settings:
Please select your own custom paper size in the application software you use ... >>
Question 2: How to set up Epson LQ-630K printer to print continuous paper? Urgent! Urgent! Urgent! 5 minutes 1, behind the printer, find two tapes similar to tank tracks, and fix the printing paper on the tracks according to the size positioning.
2. On the left side of the front of the printer, there is a small switch (the one with scale is not, the one with scale is used to adjust the paper thickness). This switch has only two gears, just dial the other gear.
3. Turn on the computer and press the paper feed button on the printer control panel to check whether the paper feed position is correct. Ok, select print on the computer as before.
It should be noted that both sides of continuous printing paper are perforated. If you don't have such paper, buy the paper you need first.
Question 3: How to connect the Epson printer? Hello, if your printer is new, you can follow the following steps:
1. Take everything out of the box, and take out all packaging tapes and packaging materials inside and outside the printer.
2. Install the paper clip and connect the power cord.
Press the power button to turn on the printer. Take out the ink cartridge from the protective packaging bag.
4. Press the maintenance key, open the upper cover of the machine, open the cover of the ink cartridge and install the ink cartridge.
5. Press the maintenance key, and the printer starts to flush ink. Please don't turn off the power when the printer is flushing ink.
6. Load the CD into the CD-ROM drive.
7. Install the printer software:
Open the CD >> click Installnaiv.exe. & gt Accept the license agreement >> Next >> Follow the prompts to complete the installation. When prompted that the printer should be connected, please connect the USB cable to the computer.
Question 4: How to set up Epson 630K printer? Express orders can be printed continuously from back to front with 10 integral. After printing one, come out from the front and print continuously on the back.
First of all, your paper size should be set. There is one on this website. Positive solution of adding paper.
Because the printer defaults to A4 paper, you should set the printer method when printing express delivery: My Computer-Control Panel-Printer-Right-click in the blank-Server Properties-Create a new format, enter a name, such as: Express Delivery Form-and then there is a length and width below, measure the size of your express delivery form, and enter-
Then there is another step, add paper type, right-click your printer, properties, there is a paper type at the top, select the type you just created, click Apply, and then on the first page of properties, you can see that there is a courier list under A4.
In addition, general express orders are printed with WORD templates, so you can also manually select paper when using WORD printers.
Question 5: How does Epson LQ-635K printer set up continuous printing? Please set up the computer, set the port, print and check 1 time again.
Question 6: How to adjust the Epson 680-K printer to continuous printing mode? The more detailed, the better. Thank you. There is an adjusting lever on the right hand side in front of the machine, which can be adjusted to sprocket feed mode, and then continuous paper can be loaded from the back of the machine.
Question 7: How does Epson's printer connect to the computer program? Thank you for installing the relevant print driver first, and then using your own connecting cable!
Question 8: How to set up continuous printing for Epson LQ-630k stylus printer to print express orders? You need to clamp the paper hole on the tractor behind the printer, then adjust the lower feed control lever and the paper thickness adjustment lever, turn on the automatic paper cutting and customize the paper at the same time.
Adjustment method of paper-passing control lever of LQ-630K printer;
The front is facing the printer, and there is a shift lever in the lower right corner of the printer, with two gears, which can be switched back and forth to adjust the forward paper and the backward paper. The position near the printer is to put the paper from the front, and the position away from the printer is to put the paper from the back.
Adjustment method of paper thickness adjusting lever of LQ-630K printer;
Open the translucent cover on the front of the printer and look to the far right. There is a bar that says-1-7. This is to adjust the thickness of the paper. If the printing paper is several layers, dial it to several positions. For A4 paper, dial 1. If it is two or three pages, dial 2 or 3.
Automatic paper cutting method of LQ-630K printer produced before April 20 14;
1. Turn off the printer.
2. Press and hold the "Feed/Return key" and "Pause key" at the same time, then turn on the printer power, press and hold for about 5s, release the print head after it starts to move, and then release the paper, and the printer will print a page of text. Find "automatic paper cutting" in the printed content to see if it is on or off. If so, go to step 3. If it is turned on, it means that automatic paper cutting has been turned on, and step 5 is executed.
3. Press the line feed key twice, the power light goes out, and the paper shortage light and pause light are always on. (Press it once, and the status of the indicator light will change each time. )
4. Press the paper feed key twice, the power light will go out, the paper shortage light will always be on, and the pause light will go out.
5. Close and complete the setup.
Automatic paper cutting method of LQ-630K printer produced after April 20 14;
1. Turn on the printer and load the printing paper. Press the "line feed/page feed (under the project)" button and the "paper feed/paper return (under the project)" button at the same time until the printer beeps and starts printing.
2. Press the "Line feed/Page feed (under the item)" button three times. Every time you press it, the printer will print a line of text, and after the third press, the paper will be cut and printed automatically. Please check whether it is on or off. If it is closed, proceed to the next step (step 3); if it is opened, proceed to step 4, indicating that automatic paper cutting has been opened.
3. Press the "Pause/(Set)" button. After you press it, an "on" will be printed on the back.
4. Press the "Line feed/page feed (under the project)" button and "Paper feed/paper return (under the project)" button at the same time, and the printer will give a long sound to save the settings.
Then, please check whether the paper size you set is exactly the same as the actual continuous paper size. If not, please choose according to the actual paper size. If the relevant paper size cannot be found, please set it as follows:
1. Custom paper:
If your computer is Windows XP:
Click "Start->" in the lower left corner of the computer; "printers and fax machines"->; "file"->; "Server Properties", check "Create a new format", enter the name of the custom size (such as 1234) in "Table Name", and enter "Width" and "Height" (height = number of continuous paper holes *0.5*2.54CM) according to the actual size of the paper. There is no need to modify the printer area margin. Click Save Format to complete the paper customization.
If your computer is Windows 7:
Click "Start->" in the lower left corner of the computer; "Equipment and Printer", click the printer icon with the left mouse button, select "Server Properties" in the upper menu bar, check "New Table", enter the name of the custom ruler in "Table Name" (for example, 1234), and enter "Width" and "Height" respectively according to the actual size of the paper (height = number of consecutive holes * 0.5). There is no need to modify the printer area margin. Click Save Format to complete the paper customization.
2. Drive settings:
Right-click the printer icon and select Printing Preferences-> "layout"->; "Advanced", in "Paper Specification", select the name of the custom size "1234".
3. Application software settings:
Please select your customized paper specification in the application software you use.
If the above scheme still fails to solve your problem, please log in to Epson official website "Online Engineer": ... >>
Question 9: How does Epson lq730k set up continuous printing 1? Pull down the front lever. Switch to continuous punch feed mode.
2. Install the punched continuous paper on the continuous paper feeder at the back of the machine.
3. Continuous paper feeding mode requires manual paper feeding. Press the "feed/eject" button to feed the paper for the first time. draw
Question 10: Is the Epson lq-680kii stylus printer easy to use? This is a 24-pin pin printer. This printer is equipped with a continuous paper feeder. When printing continuously, fix the paper cards with holes on both sides on the continuous paper feeder, and then set the driving settings for continuous printing, so that continuous printing can be performed, which is relatively easy to use and will not deviate even if printing a lot.